thermal shock test chamber – ts-72p

图片仅供参考


temperature main features
温度主要特征

★work trough temperature range: -40°c/+150°c
工作槽温度范围：-40°c/+150°c

★temperature resume time:≦5 minute
温度恢复时间:≦5分钟

★high temperature trough temperature range:60°c/+200°c
高温槽温度范围：60°c/+200°c

★low temperature trough temperature range:-65°c/0°c
低温槽温度范围：-65°c/0°c

★temperature variation rate: (nonlinear values with load and ambient temperature +10/+30°c):
温度变化速率（+10/+30°c温度下，不带负载时的非线性值）：
heating from rt to +150°c: at 20minute
cooling from 0°c to -40°c: at 20 minute
升温从rt到 +150°c 20分钟内
降温从0°c 到 -40°c 20分钟内

★load:plating sanitation
负载： 空载

★ high and low temperature concussion invariablenes time:about 30minute
高低温冲击恒温时间:约 30分钟

★test method:
1. the temperature is according to gb/t 5170.2-1996 inspection methods.
2. the reference sensor is installed on blow-out of air conditioning unit.

dimensional main features
尺寸主要特征

★internal capacity: 72 liters
内部有效容积：72升

★internal dimensions: mm 450 x 400 x 400 (w x d x h)
内部有效尺寸：mm 450 x 400 x 400 (宽 x 深 x 高)

★ external dimensions: mm 1650 x 1730 x 1800 (w x d x h)
箱体外部尺寸：mm 1650 x 1730 x 1800 (宽 x 深 x 高)




cooling system
制冷系统

★cooling: the cooling part is the primary part of the cooling equipment , it supply all the quantity of cool which the equipment want to fall temperature and maintain . base on the differentia of test state, the cooling system will turn on, and offer cooling for the test course to attain the aim of equipment performance, . the equipment’s mechanical cooling used steam compress cooling . the basic theory cooling is as follows:
steam compress cooling is most economic and most broad cooling mode . it also the most usefulness in the climatic chamber equipments . it’s theory is the freon liquid vaporize from the cooled ob-ject and tak its heat out , as the drawing follow (vaporized and compress cooling circle course sketch map) . the liquid comed into the evaporator after throttle equipments . and vaporize after gained the latent quantity of heat . the gas after vaporize is low-cool and low-pressure . tis gas is inbreathed by the compressor . after compress , the high-tempreture and high-pressure gas came into the air condensator . after water condensator the refrigerants became high-pressure liquid . the high-pressure liquid came into the evaporator . such cycle repeated . the refrigerants absorb the quantity of heat , achieve cooling . than release the quantity of heat from the high ob-jects


售 后 服 务

中国售后服务中心： 宏瑞达科技（苏州）有限公司
地址：江苏省苏州市吴中区浦庄大道浦庄工业园12号

1 安装、调试
horad公司工程师可在买方准备好设备所需外部条件（如水、电等）后，负责该设备的安装、调试、启动工作，并提供良好的技术支持和售后服务，同时对使用人员进行设备现场培训，保证受训人员能够独立、熟练操作设备和完成简单的维修工作、设备日常维护等工作。


2 保修
设备的保修期为一年，正式生效日期为买方在该设备的验收合格书上签字之日起计算。在保修期内，卖方负责该设备由于设备自身原因而引起的各种故障问题并负责无偿解决。在保修期外，该设备的维修工作要收取备品备件的成本费用和一定的服务费用。


3 维修
维修反应时间为：24小时内响应
卖方在接到买方的故障通知后，保证在24小时内做出响应，并争取在短的时间内尽快排除故障。


4 终身服务项目
卖方承诺在该设备的使用期间，可无偿、无限期地提供该设备的技术支持工作。